NEW!FED Driveline cover.$79.95 each. Bolts to pinion support of your 9" center section and covers the driveline to the rear of the transmission. Made from 5 inch diameter .065 steel tubing with 1/8" tabs, 1/4" flange secures it to your pinion support. Kit comes with 12" cover halves, 4 cover tabs, 1 pinion support tab, and hardware. Custom lenghts available. Add $40.00 fully welded.
NEW! Dimple tool. $16.95. Simple, effective way to dimple your panels for flush quarter turn fasteners. Dimple tool and panel marker (below) available as a pair for $20.00!
NEW! Panel marker. $6.00. Smart, simple tool. Place in your quarter turn fastener tab, with or without the spring, position your panel and give it a tap. Locates perfectly every time!
NEW! Fuel cap and bung. $32.00. Aluminum fuel cap with aluminum weld bung. 2 1/2 thread with o-ring seal. 2 1/8 opening, satin finish.
NEW! Rearend fill cap. $25.00.Aluminum cap with steel bung, great for rearend filling / ring gear inspection.Also available with aluminum bung for valve covers.
749101 pack of 2, $4.60 small motor mount tab. 1/8" mild steel, 3/8" hole. Fits 1 1/4" tube, can be ground to fit larger tube. also available individually, $3.00 each
749102 pack of 2, $6.50 large motor plate tab. 1/8" mild steel. Fits 1 1/4 tube, can be ground to fit larger tube. No hole, great for rear motor plate mounts.Available individually, $3.75 each
749103 pack of 2, $3.50 steering clevis. Fits 3/8" rod end and 3/4" tube,great for making steering linkages. Available individually, $2.65 each
749104 pack of 2, $7.00 Radius rod bracket fits 3/8" rod ends and any size tube. Easiest, cleanest way to mount radius rods to your chassis. Available individually, $4.00each
749105 10 pack, 13.00. Universal tab. 1/8" thick, 3/8" hole. Universal tab has a wide variety of uses. Available individually, $1.50 each
749106 $21.95 each. Rearend housing bracket. 1/4" thick mild steel, 3" center hole with four 7/16" bolt holes. Meets all sanctioning body specs.
749107 $21.95 each. Rearend chassis bracket. 1/4" thick mild steel, four 7/16" bolt holes. Generous extra material so you can trim to fit your chassis. Meets all sanctioning body specs.
Full Bore Super Buttons.10 pack $15.00.500 grip length, steel, flush mount.
Also available individually. $2.00 each
749110 10 pack, $8.00 Quarter turn fastener springs. 1 3/8 center to center. Can be adjusted to fit different button lengths. Single springs,$1.25
749111 10 pack, $6.00 Quarter turn fastener weld tab. For 7/16 button. Welds to chassis and mounts spring to secure panels. Single tab, $.90
749112 $23.00 each, with easy turn star wheel,left. Wheelie bar adjuster. 3/4" fine thread, 7/8" hex.Left hand on one end, right hand on the other. Approximately 3" adjustment. Add $17.00 for complete assembly with weld bungs and jam nut.
749114 $7.50 each. Steering column support. 3/8 UHMW plastic, .760 center hole, 3 .260 mounting holes. Ultra slick, lightweight, easy to mount. These can be mounted on the back of a piece of aluminum to support your steering column.
749115 $7.50 each. Drag link support. 3/8 UHMW pastic, .760 center hole, 2 .260 mounting holes, fits 1 1/4 tube. Ultra slick, lightweight, easy to mount with matching bracket. Makes your steering super slick.
749115A$3.75 each. Drag link support tab. 1/8 steel. Identical to the lower half of our drag link support, making mounting a snap!
Transmission handle. $24.95.This little gem takes the struggle out of lifting your powerglide in and out of the car. CNC cut from 1/4 steel, it's light enough to leave on all the time.Fits powerglide only.
Content copyright . DRAGSTERSUPPLY.COM. All rights reserved.